







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Cutler Bay Homeowners Choose Toto Construction
We provide independent Toto construction service in Cutler Bay for homeowners who already own Toto fixtures and want them diagnosed, repaired, or installed by technicians who know the brand’s real behavior in South Florida. Our crew has handled everything from Drake toilets to Washlet bidet seats across Miami-Dade, and we bring that product-specific experience to every job. Bradford Remodeling Co Cutler Bay is not affiliated with, authorized by, or endorsed by Toto. We’re an independent service provider.
That independence is the point. Toto builds a genuinely good toilet and a genuinely complicated bidet seat, and both behave differently in Cutler Bay’s hard water and humid air than they do in the dry, soft-water markets where the spec sheets were written. Most of what we fix here comes down to scaling, moisture, and original installation details that only surface after a decade of coastal weather. We work on Toto as part of our broader bathroom remodeling and repair work, and we put a written price in front of you before any tool comes out.
Why Trust Bradford Remodeling Co Cutler Bay for Your Toto Construction?

Our technicians have up to 22 years of experience, and the ones we send on Toto work have actually taken the fill valves apart, not just read the install manual. We know that a Drake’s fill valve and flush tower wear on a different schedule than a builder-grade toilet because of the specific pressure and mineral load in this part of Miami-Dade. We know that a Washlet’s electronics live in a housing that traps humidity. We know that a one-piece Ultramax sits on its flange differently than a two-piece, and that the wax ring and flange condition underneath it decide whether you get a slow leak or a sewer smell six months later.
We source OEM-compatible Toto parts for the components that matter, and we protect your warranty by servicing the fixture the way it was designed to be serviced rather than forcing a generic part into a Toto-specific fit. Every job receives a written price before work begins, and every completed job is covered by our 365-Day Done Right Promise. If the work fails inside that year, we come back and correct it at no charge. A live person answers the phone any time, day or night, so you’re not leaving a message into a queue when a toilet is running or a Washlet has gone cold.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Toto Construction Problems We Fix in Cutler Bay
These are the failures we actually see on Toto fixtures in Cutler Bay, and the reasons behind them.
- Washlet control boards and water heaters failing at four to six years. The seat housing on a C100, C200, or S350e traps moisture, and over a few humid summers that moisture reaches the board and the heating element. The usual symptoms are no spray at all, or cold water only no matter what temperature you set. It’s a moisture problem more than an electrical one, and it’s why we treat Washlet service as climate work, not just a part swap.
- Drake and Eco Drake fill valves wearing out early. Cutler Bay’s water carries enough mineral content that fill and flush valves scale up faster than the manufacturer’s service window suggests. You’ll notice the toilet running intermittently, a weak flush, or the tank refilling on its own in the middle of the night. Left alone, a running Drake can waste real money on a Miami-Dade water bill.
- Wax ring failures and floor flange corrosion on Toto one-piece toilets. The Ultramax and Ultramax II sit low and heavy, and when the flange underneath corrodes, the seal gives way quietly. What you see is a slow leak at the base, a wobble, or sewer odor in the bathroom. By the time it’s visible, the flange often needs attention too.
- Loosening or rusting undermount brackets on Soiree and Guinevere lavatories. The brackets that hold an undermount sink to the counter corrode in humid, salt-laden air, and the caulk line at the rim starts to fail. A sink that’s dropped even a fraction can crack a countertop edge or let water behind the cabinet.
- Original install details that catch up with the fixture. A lot of the housing around US 1 went up in the 1980s through the 2000s, and Toto fixtures installed during kitchen and bath updates in that era are now meeting a shutoff valve, supply line, or flange that’s as old as the house. When we open up a toilet, we look at every one of those, not just the part that failed.
Toto Parts & Our Repair-vs-Replace Approach

We source OEM Toto parts for the critical components: fill valves, flush towers, and Washlet control boards whenever they’re available. For wear items like wax rings and supply lines, we use quality aftermarket equivalents, because in those cases the branded part and the good generic do the same job at different prices, and we’d rather put your money into the component that actually fails. We don’t claim to stock parts locally; parts are sourced for each job based on what your fixture needs.
Repair or replace is an honest call, and we make it in front of you. If a Washlet’s electronics are shot, we’ll tell you when a new seat is the more cost-effective path than board-level repair. If a Drake needs a fill valve and a flapper, that’s a repair, not a replacement. If an older one-piece has a cracked base, replacement is the only sensible answer. You’ll get the reasoning and the written price before anything is ordered. Call (833) 620-5491 to talk through what your Toto is doing and get an estimate.
Our Toto Service Process – Step by Step
- 1
Diagnosis. We test the fixture in place before quoting. On a Washlet, that means checking the control board and water heater and looking for moisture in the seat housing. On a toilet, it means testing the fill valve and flush tower and pulling the fixture to inspect the flange and wax ring if a leak or odor points there.
- 2
Written repair or install plan. You get the scope and a written price before work starts. No numbers that move at the door.
- 3
Repair or install. We use OEM Toto parts for critical components and set the fixture back on a properly prepared flange and seal. On a remodel, we treat the rough-in and the substrate as part of the job, not an afterthought.
- 4
Test. We run the fixture through a full cycle, check for leaks at the base and supply, confirm the Washlet sprays hot and cold on command, and verify the flush volume and refill.
- 5
Warranty. The job closes with a clean site, a documented scope, and your signed written guarantee in hand. Our 365-Day Done Right Promise covers the work for a full year.
See the difference
Before
After
Before
After
Before
AfterToto Products We Service & Install in Cutler Bay
We service and install the Toto lines our Cutler Bay customers actually own: the Drake and Eco Drake toilets, the Ultramax and Ultramax II one-piece toilets, the Washlet bidet seats including the C100, C200, and S350e, and the Soiree and Guinevere undermount sinks. That covers the fill and flush internals, the seat electronics, the wax ring and flange work underneath, and the bracket and caulk details on an undermount lavatory. If your fixture is a Toto model not listed here, call and describe it. The underlying service is usually the same even when the part number isn’t.
We Also Service These Brands
Toto work is one part of what we do, and we’d rather be the contractor who handles the whole bathroom than a single-brand specialist. We work with KraftMaid cabinetry, Kohler fixtures, and Cambria and Silestone surfaces, install and service them to the same written standard, and coordinate them with your Toto fixtures so the vanity, the shower, and the toilet all come together on one scope and one price.
FAQs – Toto Construction Service in Cutler Bay

No. We are an independent Toto service provider and are not affiliated with, authorized by, or endorsed by Toto. We service and install Toto products using our own technicians and OEM-compatible parts, and we make that distinction clear so you know exactly who’s doing the work.
Yes, for critical components. We source OEM Toto parts for fill valves, flush towers, and Washlet control boards whenever they’re available, and use quality aftermarket equivalents for wear items like wax rings and supply lines. We’ll tell you which is which on the written quote before anything is ordered. Call (833) 620-5491 for a parts-specific estimate.
Most Toto toilet repairs, like a fill valve or wax ring, are a single visit. A Washlet control board or water heater diagnosis is usually same day, with the parts order adding the wait. A vanity or walk-in shower remodel that incorporates Toto fixtures runs longer, and the timeline depends on permit cycles and storm season in Miami-Dade. Call (833) 620-5491 for a written timeline on your job.
We cover the Drake and Eco Drake, the Ultramax and Ultramax II, the Washlet seats including the C100, C200, and S350e, and the Soiree and Guinevere undermount sinks. If your model isn’t listed, call and describe the symptom; the service approach usually carries over.
Servicing a Toto fixture with OEM-compatible parts the way it was designed does not, in our experience, void the manufacturer’s warranty. Using the wrong part in a Toto-specific fit can, which is why we source OEM for the critical components. We’re an independent provider and don’t speak for Toto, so confirm the terms of your specific warranty. Call (833) 620-5491 and we’ll walk through what your job involves.
Toto service costs depend on the fixture and the scope. A toilet repair or Washlet part replacement is a fraction of a full remodel. Here are our current ranges for the most common Toto-integrated projects in Cutler Bay:
| Service | Price Range |
|---|---|
| Bathroom Remodel | $9,000 – $28,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Bathroom Vanity Installation | $800 – $3,000 |
Every project receives a written price before work begins, so the number you see is the number you pay. Call (833) 620-5491 for an exact quote. Estimates are free.
Book Your Toto Service in Cutler Bay, FL
Whether your Washlet has gone cold or you’re planning a bathroom remodel around Toto fixtures, we’ll give you a straight diagnosis and a written price before any work starts. Our technicians bring up to 22 years of experience, and every completed job carries our 365-Day Done Right Promise. Call (833) 620-5491 to schedule your free estimate today.
Written by the team at Bradford Remodeling Co Cutler Bay.












